LUDLUM 4525 Скачать руководство пользователя страница 82

Страница: 82 / 106

Model 4525 Gate Monitor

Operator’s Manual

Ludlum Measurements, Inc.

Page 74

May 2018

RPM Operation

This section is dedicated to the operation of the RPM apart from the system

computer and software, except where noted.

Controls and Functions

The following is a description of the controls and functions on the electronics

panel, which is housed within the master detector enclosure.

READOUT

: Liquid Crystal Display (LCD), 4-line by 20-character

alphanumeric display, backlit while on AC power. Setup information,
background, and count data is displayed.

ENTER

Key

: Selects or advances the display. If the

ENTER

key is pressed

while turning the instrument on, the Model 4525 is loaded with a set of

default parameters.

LINE FUSE

: Fuse to limit current from the AC mains input. The fuse is

250 Vac at 1A (AGC1) or equivalent.

BAT FUSE

: Fuse to limit current from the battery. The fuse is 10A

(ABC10) or equivalent.

Mains Supply

: Line Voltage input of 100-240 Vac, 50-60 Hz, 250 W.

BATTERY

: Back-up power is provided by a 12 V, 12 amp/hr battery.

Power on Self Test (POST)

When the RPM is first powered up, all relays, lights, and audio devices are

momentarily activated. This POST is done in order to give the user an
opportunity to ensure that all applicable devices are working. The test lasts

for about three seconds and may be activated anytime by pressing the

RESET

button for greater than five seconds, or by selecting the Reboot function

within the software (Set Parameters window).

After POST, the system will establish the level of background radiation. On
the remote display, the

POWER OK

indicator turns on, and the

CHECKING

indicator blinks for 30 seconds. At the end of the background update, the

Section

Содержание 4525











































































































Результаты поиска

Содержание 4525

Отзывы:

LUDLUM 4525, Руководство оператора, Страница: 82 / 106

Результаты поиска

Содержание 4525

Отзывы: