LUDLUM 4525 Скачать руководство пользователя страница 36

Страница: 36 / 106

Model 4525 Gate Monitor

Operator’s Manual

Ludlum Measurements, Inc.

Page 28

May 2018

Warning Markings and Symbols

Caution!

The operator or responsible body is cautioned that the protection

provided by the equipment may be impaired if the equipment is used in
a manner not specified by Ludlum Measurements, Inc.

ODEL

4525

ELECTRONICS

(

IN DETECTOR HOUSINGS

)

ARE MARKED

WITH THE FOLLOWING SYMBOLS

ALTERNATING CURRENT (AC)

(IEC 417, No. 5032) - designates

an input receptacle that accommodates a power cord intended for
connection to AC voltages. This symbol appears next to the power input

receptacle.

PROTECTIVE CONDUCTOR TERMINAL

(per IEC 417, No. 5019) –

designates the central grounding point for the safety ground. This symbol is

visible inside the master enclosure.

CAUTION

(per ISO 3864, No. B.3.1) – designates hazardous live voltage

and risk of electric shock. During normal use, internal components are
hazardous live. This instrument must be isolated or disconnected from the

hazardous live voltage before accessing the internal components. This
symbol appears on the bottom panel and inside the master enclosure.

Note the following precautions:

Warning!

The operator is strongly cautioned to take the following precautions to

avoid contact with internal hazardous live parts that are accessible using
a tool:

1. Turn the instrument power

OFF

and disconnect the power cord.

2. Allow the instrument to sit for one minute before accessing internal

components.

The “

crossed-out wheelie bin

” symbol notifies the consumer that the

product is not to be mixed with unsorted municipal waste when discarding;

each material must be separated. The symbol is placed near the AC
receptacle. See Section 13, “Recycling,” for further information.

Содержание 4525











































































































Результаты поиска

Содержание 4525

Отзывы:

Похожие инструкции для 4525

Бренды по названию

Популярные бренды

LUDLUM 4525, Руководство оператора

Результаты поиска

Содержание 4525

Отзывы:

Похожие инструкции для 4525

Бренды по названию

Популярные бренды