Lucent Technologies CAJUN P120 Скачать руководство пользователя страница 47

Страница: 47 / 130

Chapter 6

Legacy CLI (Command Line Interface)

Cajun P120 User’s Guide

Note:

1) After entering a value, you cannot go back and change it at this time. You must

either complete the setup command or break the setup command with Ctrl-Q.
Then re-enter simple-setup or use the set command for a specific
group/parameter.

2) If keyboard activity is not detected for 10 minutes, then you are automatically

removed from the simple-setup command and Privileged level. Any changes
you have made are lost. You can re-enter the simple-setup command.

The next parameter displays automatically.

setup> def-gateway [0.0.0.0]?

You may now set the Cajun P120’s default gateway IP address. Either:

•

Keep the default setting by pressing Enter, or

•

Type a new value and press Enter. For example, to change the IP address,
enter:

194.90.121.1

The next parameter displays automatically.

setup> bootp-mode [never]?

You may now set the Cajun P120’s Bootp mode. Either:

•

Keep the default setting by pressing Enter, or

•

Type a new mode and press Enter. The possible values are:
— once – Attempts to configure parameters from the Bootp client server when

the Cajun P120 is powered on. Once Bootp is successful, then the setting is
automatically changed to ’never’.

— always – Attempts to configure parameters from the Bootp server each time

the Cajun P120 is powered on.

— never – Does not attempt Bootp.

For example, to stop the bootp process, enter:

never.

Note:

We recommend that you set the bootp-mode to

never.

The next parameter displays automatically.

setup> slipip [192.168.10.1 255.255.255.0]?

You may now set the Cajun P120’s SLIP address. Either:

•

Keep the default setting by pressing Enter, or

•

Type a new value and press Enter. For example, to change the IP address,
enter:

194.90.120.2 255.255.255.0

The next parameter displays automatically.

setup> slip-peer-ip [192.168.10.2]?

Содержание CAJUN P120



































































































































Результаты поиска

Содержание CAJUN P120

Отзывы:

Похожие инструкции для CAJUN P120

Бренды по названию

Популярные бренды

Lucent Technologies CAJUN P120, Руководство пользователя

Результаты поиска

Содержание CAJUN P120

Отзывы:

Похожие инструкции для CAJUN P120

Бренды по названию

Популярные бренды