Lucent Technologies CAJUN P120 Скачать руководство пользователя страница 65

Страница: 65 / 130

Chapter 6

Legacy CLI (Command Line Interface)

Cajun P120 User’s Guide

If you try to add a MAC address to a non-secured port (Port #1 in this case) you get
the following error message:

CajunP120-priv# add mac 00-65-5b-86-5b-82 1 2

ERROR: Try to add secured MAC to non-secured port 1

Delete MAC Command

Use this command to delete an address from the secure table. The required
parameter is the address and the VLAN number. If the port was not specified, the
address shall be cleared from all ports.

The syntax of this command is:

Delete MAC {MAC_address [port_number [vlan_number]]}

Examples:

CajunP120-priv# delete mac 00-60-5c-86-5b-81 2 3

Address 00-60-5c-86-5b-81 was deleted from the secure list !

CajunP120-priv#

If you try to delete a MAC address from a non-secured port (Port #1 in this case)
you get the following error message:

CajunP120-priv# delete mac 00-65-5b-86-5b-82 1 2

ERROR: Try to delete secured MAC to non-secured port 1

Содержание CAJUN P120



































































































































Результаты поиска

Содержание CAJUN P120

Отзывы:

Похожие инструкции для CAJUN P120

Бренды по названию

Популярные бренды

Lucent Technologies CAJUN P120, Руководство пользователя

Результаты поиска

Содержание CAJUN P120

Отзывы:

Похожие инструкции для CAJUN P120

Бренды по названию

Популярные бренды