LRX VULTURE Скачать руководство пользователя страница 11

Страница: 11 / 21

LRX

VULTURE

Check for the latest manual updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

VULTURE SPECIFCATIONS

Electrical:



Volts: 90-240 AC – non-dimmed feed line.



Hertz: 50/60



Amps: 2.0 - 7.0 with Trolley



U- Ground plug



Battery 12VDC



Data: XLR 5 pin connector

Physical:



Tilt: 40 degrees above horizontal to 90 degrees below horizontal



Pan: 340 degrees



Weight: 120 pounds approx.



Fixture mounting hooks have been designed to mate with truss diameter
chords not greater than two inches (50.8mm).

INSTALLATION OF FIXTURES

TELESCOPIC TYPE MAN LIFTS



THIS FIXTURE MUST BE MOUNTED ON A LEVEL TRUSS.



Installation structure must be designed and approved to safely carry all
anticipated loads.



It is the user’s responsibility and obligation to determine and comply with all
applicable laws and regulations.



The installation and operation of this unit must be carried out by authorized
and qualified personnel.



Hanger bolts in hanger assembly must be installed. Both ratchet straps must
be clipped onto their respective anchor point.



Ratchet straps require minimum of 1.5 wraps on the ratchet to ensure they
remain tight.



Always use approved safety cables secured to a point capable of supporting
the total weight of the load.



All power and data cables

must have a strain relief attached.



If cable rollers are required refer to “LRX Cable Roller” manual.

Содержание VULTURE






















Результаты поиска

Содержание VULTURE

Отзывы:

Похожие инструкции для VULTURE

Бренды по названию

Популярные бренды

LRX VULTURE, Руководство пользователя

Результаты поиска

Содержание VULTURE

Отзывы:

Похожие инструкции для VULTURE

Бренды по названию

Популярные бренды