Lovato ADXL 0030 600 Скачать руководство пользователя страница 1

         Doc: I456GB06_16.docx             

      29/06/2016

 

p. 1 / 20

ADXL…  

SOFT STARTER

 

 

INSTRUCTION MANUAL

 

 

Read the manual carefully before installation and use.

These devices must be installed by qualified personnel, in compliance with current plant-engineering regulations, in order to avoid damage to persons or property. 

Before any maintenance operation on the device, switch off power supply from measuring and supply inputs.

The manufacturer assumes no responsibility for electrical safety in the event of improper use of the device. 

The products described in this document are subject to updates or modifications at any time. Data and descriptions in the catalogue therefore do not have any contractual value.

The building’s electrical system must incorporate a switch or circuit breaker. It must be installed close to the equipment and within easy reach of the operator. It must be marked as the disconnecting 

device of the equipment: IEC/ EN 61010-1 § 6.12.2.1. 

Clean the instrument with a soft cloth. Do not use abrasives, liquid detergents or solvents. 

Contents 

Page 

Description  

Front button functions 

Front LEDs 

Display indications 

AUTOSET guided configuration 

Navigating the display pages

  

Operational status

 

Remote keypad

 

Startup methods 

Protections

Motor thermal protection 

Motor thermal protection via PTC 

Starter thermal protection 

Main menu 

Password-protected access 

Inputs, outputs, internal variables 

Limit thresholds (LIMx) 

Remote variables (REMx) 

User alarms (UAx) 

IR programming port 

Parameter setting from PC 

Parameter setting from smartphone or tablet with CX02 Wi-Fi dongle 

Parameter setting from smartphone or tablet with NFC 

Parameter settings (setup) from front panel 

10 

Parameter table 

10 

Alarms

13 

Alarm properties 

13 

Table of alarms 

14 

Description of the alarms 

14 

Programmable input functions table 

14 

Programmable input defaults settings 

15 

Programmable output functions table 

15 

Programmable output defaults settings 

15 

Commands menu  

16 

Installation

16 

Recommendations

16 

Power factor correction 

16 

Connection diagrams 

17 

Mechanical dimensions  

18 

Terminal layout 

18 

Choosing the soft starter 

19 

Type 2 coordination 

19 

Technical characteristics 

19 

Manual review history 

20 

I456GB06_16      

Содержание ADXL 0030 600





















Отзывы: