23
ADJUSTABLE BED FRAME - OWNER’S MANUAL //
IMPORTANT
Sync Mode allows you to control two Bed Frames with one Remote Control. If you only have
one Bed Frame continue reading at the next chapter.
SYNC MODE
%HIRUHFRQ¿JXULQJ6\QF0RGHSOHDVHHQVXUH
ƒ
Both Bed Frames are standing next to each other
ƒ
The Bed Frames will not collide with each other when moving
ƒ
Each Bed Frame can be controlled using its own Remote Control
MOVING THE BED FRAME UP AND DOWN IN SNYC MODE
When Sync Mode is activated, pressing the UP and DOWN Buttons on ei-
ther of the Remote Controls will move both Bed Frames simultaneously.
FIXING MISALIGNMENT
To activate Sync Mode:
1. Ensure both Bed Frames have been disconnected from the Power Outlet.
2. Connect the Control Boxes of the two Frames with the Sync Cable (X). This should be in-
serted into the port marked "CAS" on each Control Box.
3. Ensure the Cable is Routed so that it does not interfere with the movement of the Bed Frames.
4. Reconnect the Bed Frames to the Power Outlet.
ƒ
If the Bed Frames do not move together, disconnect from the Power and repeat the steps.
ƒ
To end Sync Mode, disconnect the Sync Cable.
,IWZRFRQQHFWHG%HG)UDPHVKDYHGLႇHUHQWVDYHG0HPRU\3RVLWLRQVSUHVVLQJD0HPRU\3R-
VLWLRQ%XWWRQZLOOFDXVHWKH%HG)UDPHVWRPRYHWRGLႇHUHQWSRVLWLRQV7KLVLVFDOOHG0LVDOLJQ-
ment. In this case, you must move both Bed Frames to their lowest position.
1. Press the Sleeping Position Button on one Remote Control
2. Wait for both Bed Frames to reach their lowest position
3. The Bed Frames are realigned. Continue using the Bed Frame as normal.
PERFORMING A FLAT POSITION RESET
To perform a Flat Position Reset:
1. Press the Sleeping Position Button for at least 10 seconds.
2. 7KH&RQWURO%R[FOLFNVWZLFHWRFRQ¿UPtheinput.
3. Perfom a Reference Drive with the Sleeping Position Button or any UP/
DOWN Button (see section "Reference Drive").
24 //ADJUSTABLE BED FRAME - OWNER’S MANUAL
DISASSEMBLY
7RGLVDVVHPEOHWKH$GMXVWDEOH%HG)UDPH\RXPXVW¿UVWGLVFRQQHFWWKH%HG)UDPHIURPWKH
mains. Then, follow the assembly instructions in reverse order. To minimize the risk of pinching
when transporting the Side Rails, secure all moving parts with packaging tape.
6. DISASSEMBLY AND
TRANSPORTATION
TRANSPORTATION
After it has been fully assembled, the Bed Frame should only be moved short distances within
the same room. Lifting the Bed Frame requires two people. To lift the Bed Frame:
1. (QVXUHWKDWWKH%HG)UDPHKDV¿UVWEHHQPRYHGWRWKH6OHHSLQJ3RVLWLRQ
2. Stand at opposite sides of the Bed Frame (long sides) and grip the Base Platform.
NOTICE
Moving the Bed Frame on its side or upside down may lead to damage to the product.
• Only move the Bed Frame while it is in horizontal position (Platforms facing upwards)
• 'LVDVVHPEOHWKH%HG)UDPHEHIRUHPRYLQJLWWRDGLႇHUHQWORFDWLRQ
CAUTION
Risk of minor or moderate injury through crushing
Tilting the Bed Frame when lifting or moving the Adjustable Bed Frame may lead to minor or
moderate injury through crushing.
• Keep the Bed Frame level while lifting or moving it
• Do not attempt to lift or move the Bed Frame alone
25
ADJUSTABLE BED FRAME - OWNER’S MANUAL //
CLEANING
NOTICE
Cleaning agents, such as non-alcohol based cleaners, sanitizers, and others can destroy the
anodized layer of the Adjustable Bed Frame. Use only a dry or slightly damp lint-free cloth to
clean the Bed Frame
MAINTENANCE
The Adjustable Bed Frame does not require maintenance. If the Bed Frame becomes damaged,
RULI\RXDUHH[SHULHQFLQJWHFKQLFDOGLႈFXOWLHVFRQWDFW/2*,&'$7$XVLQJWKHGHWDLOVRQSDJH
7. CLEANING AND
MAINTENANCE
WARNING
Moderate risk of death or serious injury through electric shocks
Leaving the Bed Frame plugged in while cleaning it may lead to death or serious injury
through electric shocks.
• Use only a dry or slightly damp lint-free cloth to clean the Bed Frame
• Do not allow any of the Bed Frame’s components to become wet during cleaning
• Always unplug the Bed Frame from the mains before cleaning
To clean the Adjustable Bed Frame, use a dry or slightly damp lint-free cloth to wipe the Bed Frame.
