22 //ADJUSTABLE BED FRAME - OWNER’S MANUAL
ACTIVATING THE CHILD LOCK
Always activate the Child Lock when children are near the Bed Frame. Proceed as follows:
1. Press and hold the
Head UP and Foot UP
Buttons for at least 6 seconds.
2. 7KH/('ZLOOÀDVKWLPHVWRFRQ¿UP7HVWWKH5HPRWH&RQWUROWRFKHFNWKDW
Child Lock has been activated.
To disable Child Lock, repeat the steps above.
If you remove the batteries from the Remote Control, the Child Lock will be deactivated
automatically.
,I\RXWU\WRRSHUDWHWKH%HG)UDPHZKLOHWKH&KLOG/RFNLVDFWLYDWHGWKH/('ZLOOÀDVK
6 times.
MOVING THE BED FRAME TO A SAVED MEMORY POSITION
Proceed as follows to move the Bed Frame to a saved Memory Position:
1. Press the Memory Position Button for the Memory Position you wish to
move to, then release.
2. Wait for the Bed Frame to move to the saved Memory Position
MOVING THE BED FRAME TO THE SLEEPING POSITION
3.
The Sleeping Position is the Bed Frame’s lowest position. While in the Sleeping Position, all
Platforms are horizontal. Proceed as follows to move the Bed Frame to the Sleeping Position:
1. Press and release the Sleeping Position Button (do not hold the Button)
2. Wait for the Bed Frame to move to the Sleeping Position
FACTORY RESET
$)DFWRU\5HVHWUHVWRUHVWKH%HG)UDPHWRWKHVDPHVWDWHDVEHIRUH¿UVWXVH$Q\PHPRU\SR-
sitions you have stored will be deleted and replaced with the pre-set memory positions. To per-
form a Factory Reset:
1. Press and hold the Foot DOWN and Head DOWN buttons for 10 seconds.
2. When the reset is complete, the Control Box will click twice.
3. Release the buttons.
To perform a Reference Drive after the Factory Reset, only release one of the DOWN buttons.
This will start the Drive automatically.
23
ADJUSTABLE BED FRAME - OWNER’S MANUAL //
IMPORTANT
Sync Mode allows you to control two Bed Frames with one Remote Control. If you only have
one Bed Frame continue reading at the next chapter.
SYNC MODE
%HIRUHFRQ¿JXULQJ6\QF0RGHSOHDVHHQVXUH
ƒ
Both Bed Frames are standing next to each other
ƒ
The Bed Frames will not collide with each other when moving
ƒ
Each Bed Frame can be controlled using its own Remote Control
MOVING THE BED FRAME UP AND DOWN IN SNYC MODE
When Sync Mode is activated, pressing the UP and DOWN Buttons on ei-
ther of the Remote Controls will move both Bed Frames simultaneously.
FIXING MISALIGNMENT
To activate Sync Mode:
1. Ensure both Bed Frames have been disconnected from the Power Outlet.
2. Connect the Control Boxes of the two Frames with the Sync Cable (X). This should be in-
serted into the port marked "CAS" on each Control Box.
3. Ensure the Cable is Routed so that it does not interfere with the movement of the Bed Frames.
4. Reconnect the Bed Frames to the Power Outlet.
ƒ
If the Bed Frames do not move together, disconnect from the Power and repeat the steps.
ƒ
To end Sync Mode, disconnect the Sync Cable.
,IWZRFRQQHFWHG%HG)UDPHVKDYHGLႇHUHQWVDYHG0HPRU\3RVLWLRQVSUHVVLQJD0HPRU\3R-
VLWLRQ%XWWRQZLOOFDXVHWKH%HG)UDPHVWRPRYHWRGLႇHUHQWSRVLWLRQV7KLVLVFDOOHG0LVDOLJQ-
ment. In this case, you must move both Bed Frames to their lowest position.
1. Press the Sleeping Position Button on one Remote Control
2. Wait for both Bed Frames to reach their lowest position
3. The Bed Frames are realigned. Continue using the Bed Frame as normal.
PERFORMING A FLAT POSITION RESET
To perform a Flat Position Reset:
1. Press the Sleeping Position Button for at least 10 seconds.
2. 7KH&RQWURO%R[FOLFNVWZLFHWRFRQ¿UPtheinput.
3. Perfom a Reference Drive with the Sleeping Position Button or any UP/
DOWN Button (see section "Reference Drive").
24 //ADJUSTABLE BED FRAME - OWNER’S MANUAL
DISASSEMBLY
7RGLVDVVHPEOHWKH$GMXVWDEOH%HG)UDPH\RXPXVW¿UVWGLVFRQQHFWWKH%HG)UDPHIURPWKH
mains. Then, follow the assembly instructions in reverse order. To minimize the risk of pinching
when transporting the Side Rails, secure all moving parts with packaging tape.
6. DISASSEMBLY AND
TRANSPORTATION
TRANSPORTATION
After it has been fully assembled, the Bed Frame should only be moved short distances within
the same room. Lifting the Bed Frame requires two people. To lift the Bed Frame:
1. (QVXUHWKDWWKH%HG)UDPHKDV¿UVWEHHQPRYHGWRWKH6OHHSLQJ3RVLWLRQ
2. Stand at opposite sides of the Bed Frame (long sides) and grip the Base Platform.
NOTICE
Moving the Bed Frame on its side or upside down may lead to damage to the product.
• Only move the Bed Frame while it is in horizontal position (Platforms facing upwards)
• 'LVDVVHPEOHWKH%HG)UDPHEHIRUHPRYLQJLWWRDGLႇHUHQWORFDWLRQ
CAUTION
Risk of minor or moderate injury through crushing
Tilting the Bed Frame when lifting or moving the Adjustable Bed Frame may lead to minor or
moderate injury through crushing.
• Keep the Bed Frame level while lifting or moving it
• Do not attempt to lift or move the Bed Frame alone
