background image

1. Before starting maintenance or disassembling the unit to replace parts, be sure to stop

air supply.

Performing maintenance or disassembly with air supplied may cause a part to jump out, oil to 

    squirt out, or the unit to perform unexpected behavior, and may result in an accident or personal
    injury.

3. 

2. 

Do not operate the tool with the Frame Head removed.

Tighten the Bleed Plug firmly before use.

Items such as fingers may become caught in the mechanism.

If the Bleed Plug is loose or coming off during use, oil may squirt out resulting in an accident or

   personal injury.

4. Do not bring your face close to the exhaust ports.

Pressurized air containing fine particles is discharged from the exhaust ports during use. Keep

    eyes away from this area.

5. Avoid skin contact with substances such as hydraulic oil, lubricating oil and grease.

Such substances may cause inflammation of the skin. If they come into contact with your skin, 

    wash the affected area thoroughly.

6. The parts to be used must be those supplied from us or recommended by us.

Select and attach parts applicable to your rivet.

Otherwise the unit may not produce maximum performance and may sometimes malfunction

    resulting in an accident or personal injury.

7. Make sure that the workplace is safe, clean and organized.

Accidents can easily occur in untidy workplaces.

If the cut

mandrels are allowed to fall onto the floor, you may slip on them, and injury may result.

8. Avoid uncomfortable postures while working.

You may fall down and injury may result.

9. Keep people who are not involved in work away from the workplace.

Accidents or injury may result.

10. Maintain the tool with proper care.

Refer to the Instruction Manual for details on replacing parts and attachments, otherwise injury may

    occur.

11. Keep the handgrip always dry and clean, and avoid adhesion of oil and grease.

Otherwise the grip may slip from your hand resulting in falling of the unit.

12. Do not leave the floor littered with cut mandrels.

Cut mandrels are dangerous because their ends are sharp. Stepping on them is also dangerous

    easily causing a slip and fall accident.

13. Use the tool carefully and concentrate on correct operation at all times.

Use the tool with proper care, paying full attention to methods of handling and operation and

surrounding conditions. Accidents and injury may result if this practice is not followed.

Use common sense at all times, otherwise accidents or injury may result.

When you are tired, do not use the tool, otherwise accidents or injury may result.

14. Ask Lobtex to carry out any repair work required.

Repair work should only be carried out by a qualified technician. Please contact your nearest

“LOBSTER” distributor, representative, or direct to Lobtex Co., Ltd., Osaka. If the tool is repaired

    by someone without the necessary qualifications and experience, the tool may not perform to
    optimum standards, and accidents or injury may result.

15. Do not attempt to modify the tool.

Unauthorized modifications may cause malfunctions which can lead to accidents or injury.

16. Only for EU countries, do not dispose of electric tools together with household waste
     material !

In observance of European Directive 2002/96/EC on waste electrical and electronic equipment

   and its implementation in accordance with national law, electric tools that have reached the end
   of their life must be collected separately and returned to an environmentally compatible recycling
   facility.

17. Important information and clue about the use are listed in main body label. When
     contents cannot read by contamination or by the damage of the label, please order
     a new label and put it.

The new label could be ordered from us(Lobtex)via distributor.

CAUTION

ⱥㄒ㸭(1*/,6+

2

Содержание R1A1























Отзывы: