background image

IMPORTANT SAFETY INSTRUCTIONS

ی

Be sure to read the following Important Safety Instructions carefully and make sure that you
understand them thoroughly before using this tool.

ی

Always wear eye-protection at all times during use. If this is not observed, the cut mandrels 
may eject out when the rivets are cut and cause serious injury.

ی

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.

ی

The Important Safety Instructions are divided into                          and                         . 
The differences between these two levels are described below.

CAUTION

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death 
or serious injury to the operator.

Important note about the installation, handling and maintenance of this product.

Indicates a potentially hazardous situation which, if not avoided, may result in  
moderate injury to the operator or physical damage.

Moreover, failure to follow the instructions marked with the                          symbol or cautions without 
a                         symbol which appear in the text of this manual may also have serious results in some 
cases. Always be sure to observe the instructions given in the Important Safety Instructions.  

CAUTION

CAUTION

CAUTION

WARNING

1. The air pressure should be kept within the range of 0.5 to 0.6 MPa (5 to 6 kgf/cm

2

, 71 to 85 psi).

If an air pressure which is greater than this is used, the tool may become damaged, and injury or

damage to property may result.

2. Never look into the nosepiece of the tool, and never point the nosepiece toward other persons.

If the tool is used while the cut mandrels are still inside the tool not being ejected, these mandrels

   may be ejected from the tool’s nosepiece during use and cause serious injury.

3. Always attach the tank case unit before use.

If you work without attaching the tank case unit, there is a risk that the mandrel of rivet that has 

    been cut is not discharged, and will be clogged inside exhaust pipe,causing a fault of the equipment.
    Also, these mandrels may be ejected from the tool’s nosepiece during use and cause serious injury.

4. Wear protective glasses during use.

Failure to do so may result in an accident or personal injury in case that a rivet or a piece of

    cut-mandrels jumps out toward you.
 

5. Make sure that the tool and the air source are connected securely.

If the threads of the joints do not match or if the screws are not inserted far enough, the air hose

   may become disconnected during use and injury may result.

Use hose bands to securely connect the air hose joint and air hose. If they are not connected

    securely enough, the air hose may become disconnected during use and injury may result.

6. Turn off the air supply before disconnecting the tool from the air source.

Compressed air may cause the air hose to whip around, and injury may result.

7. Check that all the tool parts are free from damage before use. Any damaged parts should

be repaired before the tool is used.

If the tool is used while any parts are still damaged, injury may result.

If the tool is damaged by objects being dropped onto it, for instance, the damaged part may break

    and accident or injury may result.

Don't pull and drag the tool by the air hose. It may trigger some damages on the tool body, 

    breakage of Rotary Joint or some other defects and lead serious troubles with injuries.

8. If using in elevated locations, use a safety harness, and take care to avoid dropping rivets

or the tool itself.

Accident or injury may result if this practice is not followed.

ی

After reading this manual, keep it in a safe place where it is easily accessible to all users.

WARNING

ⱥㄒ㸭(1*/,6+

1

Note

Содержание R1A1























Отзывы: