20
Установка
Instalación
Installation
Installation
EN
Transport
Fig.1.
Fitted with personal protection equipment,
transport the appliance to the installation location.
Use suitable equipment, capable of dealing with its weight:
persons not involved with the appliance installation may not pass
through or stand in the work area during the appliance assembly.
During the transport, pay particular attention to passing through
openings and/or doors.
Model
Weight
SILEA 20
80 kg [176,3 lb]
SILEA 30
103 kg [227 lb]
Preliminary operations
Fig.2.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy
water but without any corrosive or abrasive products or sharp or
pointed instruments.
Check that all the parts making up the product are in
good condition and without any faults or breakages, if
that is not the case, contact the Retailer for the procedures
to follow.
Positioning
Fig.3.
Install the appliance in a room:
• dedicated and suitable to the cooking of food;
• having adequate air ventilation;
• containing no flammable or explosive elements;
• that complies with the current regulations on health and
safety and systems in your country;
• is protected from the weather;
• has a maximum temperature of b5° (41°F) and +35°C
(95°F);
• has a maximum humidity of 70%.
To reduce the risk of a fire,
comply with the stated
minimum distances
and install the appliances in
fireproof
rooms and
not at risk of explosion
. The floor
of the installation room must also have a
fireproof
surface finish.
Serial number plate reading
Fig.4.
The serial number is on the back of the appliance.
It provides important technical information that is vital in case of
a request for maintenance or repair of the appliance: please do
not remove, damage or modify it.
Electrical connection
The electrical connection must be carried out
exclusively
by qualified personnel after reading the safety warnings
at the beginning of the manual.
Before installing the appliance,
check that systems
comply with the regulations in force
in the country
where it is going to be used and
with the specifications
indicated on the appliance rating plate
on the LH side of the
product.
• machines
have
the power cable already installed; a plug
(not supplied) must be fitted to it
of suitable capacity.
This operation must be carried out by qualified personnel.
For a correct electrical connection, the appliance must:
• be included in an
equipotential system
Fig.6.
in
compliance with the legislation in force. This connection
must be made between the various devices with the terminal
marked with the equipotential symbol
. The cable must
have a maximum cross-section of 10 mm
2
(in compliance with
IEC EN 60335-2-42:2003-09) and must be yellow-green;
• must be
grounded
to the mains (green-yellow wire);
• must be connected to a
circuit breaker
in compliance with
the regulations in force (0.03A A type);
• must be connected to an
omnipolar circuit breaker
allowing
complete disconnection in overvoltage III category conditions.
The Manufacturer accepts no liability for failure to comply with
the above.
If required, the cable must be replaced by the Dealer or its
technical service or by a person with similar qualifications
to prevent any risk.
Pre-testing and final inspection
The product is checked and tested in the Manufacturer’s plant
before being delivered to the customer.
The “production process check sheet” enclosed with it guarantees
that each step in the production process, from assembly to
packaging, was carefully checked from both the operating and
safety standpoints.
Operations to carry out before delivery of the product to the
customer.:
• Check the direction of rotation of the bowl (indicated by the
arrow on the sticker) is correct
• Start the appliance following the instructions in the “Use and
Maintenance” manual annexed: monitor it during the whole
test and check that all the electrical components work properly.
• At the end of the test, you
MUST
activate the guarantee.
IF IT IS NOT REGULARLY ACTIVATED, THE VALIDITY OF
THE SAME STARTS FROM THE INVOICE DATE AND NOT
FROM THE ACTUAL INSTALLATION DATE.
Installation
Installazione
Содержание Cuppone Silea
Страница 1: ...Silea MIXER Quick Guide...