background image

 
 

Explo Trainer 

User’s Manual 

Version 1.1 | 18/06/19 

 

Page 17 

 

 

Precautions and safety instructions 

 

The Explo Trainer system is a simulation system. For reasons of safety, the system does not detect 
gas but ultrasonic signals. The system therefore cannot be used as a real gas meter. 

Do not use the 

system in an environment in which you suspect that there may actually be a potentially 
explosive mix of gases! 
 

 

The system is not waterproof. Never use it in the rain or in places where fire -extinguishing materials 
are used. Contact with water may permanently damage the system, in which case any resulting 
damage will not be covered by the product guarantee. 
 

 

Never use the system if the casing or cables are damaged and if you suspect a potential risk for the 
instructor or trainee. In this event, contact the manufacturer and have the system repaired.  
 

 

If necessary, clean the equipment with a damp cloth (using a mild all -purpose household cleaning 
agent if necessary). The casing is not resistant to chemicals such as alcohol, thinner or acetone. 
 

 

If no units are being charged, disconnect the battery charger from the mains power.   
 

 

Once the training session has been completed, it is best to store the set back in the supplied carry 
case. You can thus be sure that the system will be well protected. 

 

Guarantee 

From date of purchase, the Explo Trainer system carries a year's full guarantee on materials, call out 
charges and hourly rates.

 

Defects caused by wrongful use, damage caused by falling or external factors that  damage the Explo 
Trainer system are not covered by the guarantee. 
 

 

Содержание EXPLO TRAINER





















Отзывы: