Lincoln Vrtex 360 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 53

background image

E-3

TROUBLESHOOTING

E-3

VRTEX

TM

360

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

POSSIBLE AREAS OF

MISADJUSTMENTS(S)

RECOMMENDED

COURSE OF ACTION

Previous weld pass data is not
accessible on the LASER screen.

Some  or  none  of  the  welding  para-
meters,  defects,  or  discontinuities
are  shown  on  the  LASER  screen
graph.

The user is not sure of which toler-
ance set they are using.

The machine was shut down and will
not turn back on when the green cir-
cular button is pressed.

The user cannot weld a second
pass.

The VR FCAW/GMAW or VR SMAW
device(s) location do not correspond
with the image shown in the FMD
(Face Mounted Display) device.

Not all of the buttons are lit on the
front of the machine.

The

VRTEX

TM

360

does not start up

when the green circular button is
pressed.

“End Pass” must be activated before
starting  a  new  pass.    If  a  new
coupon  is  started  the  data  will  only
be available for the first pass.   Again
“End  Pass”  must  be  pressed  before
a new pass is started

These items may be “toggled” off.

The tolerance set displayed in the
tolerance editor is the one being
used.

The tolerance set can also be read
from the student report.

The system may still be in the shut
down mode.

The joint configuration may set up
for one pass only.

The system may be located to large
metal objects.

Only the buttons that are available
for use light up.

Make sure the correct input power is
being applied to the machine.

Use  the  joystick  to  go  to  pass  num-
ber and change which pass data you
are looking for.  Note that some con-
figurations only have one pass capa-
bilities.   See the Lincoln default tol-
erances.

Use  the  joystick  to  highlight  the
desired items and then press the red
select  button  to  toggle  them  on.
Also,  make  sure  that  you  are  on  a
currently welded pass.

Go to the instructor mode to change
tolerances. Go to the login screen,
turn the key and select tolerances to
verify tolerance set.

See the Operation Section in this
manual.

Wait 20 seconds, then press and
hold the green circular button for 3
seconds to start the machine.

Check the tolerance editor to verify
the joint configuration allows for mul-
tiple pass welding.

Move the system to a suitable loca-
tion. See the Installation Section of
this manual.

N/A

Be sure to hold the green circular
button in for at least three seconds.

«
...
46
47
48
49
50
...
»

Содержание Vrtex 360






















































Отзывы:

Нет отзывов

Похожие инструкции для Vrtex 360

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 2

Бренд: FBII Страницы: 48

Бренд: HAI Страницы: 2

Бренд: RAM Страницы: 32

Бренд: HALDER Страницы: 7

Бренд: Velleman Страницы: 3

Бренд: M-system Страницы: 9

Бренд: QSC Страницы: 4

Бренд: CAMDEN Страницы: 2

Бренд: Falcon Страницы: 3

Бренд: Nalnor Страницы: 8

Бренд: Westlake Audio Страницы: 21

Бренд: Malone Страницы: 19

OPTIUTA10B Optidrive Series

Бренд: Lanzar Страницы: 8

Бренд: EAE Страницы: 50

Бренд: CAME Страницы: 20

Arc Welder 55 - 160A

Бренд: Silverline Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды