58
9.4 New mounting or replacement of a
flow limiter module while retaining the
base plate module
<
CAUTION
Burn injury hazard
Escaping oil is possibly hot
•
Interrupt the oil feed to the flow limiter.
•
If necessary, clean the flow limiter to remove any external
impurities.
•
If necessary, detach the electrical quick-coupling connectors
at the module to be replaced and place them aside.
•
Ensure that the oil contained in the lubrication system has
cooled down.
9.4.1 New mounting with existing dummy
module or replacement of an SMBM-X
module
See Fig. 40
Table 44
Required parts
Item Designation
Quanti
ty
Part number
<Content>
11
SMBM-X module / SMBM-
V module
1 see order code
9 Hexagon
socket
screw
M8 x 40 mm
1
DIN912-M8x40-
8.8
8 Hexagon
socket
screw
M8 x 100 mm
1 2010-00000007
6 Packing ring (O-ring)
2 WVN532-12x2
4 Plug
screw
1 2030-00000002
Parts on hand
2 Complete dummy module
1 24-0711-2406
9.4.1.1 General work steps
•
Loosen and remove the two hexagon socket screws (M8, WAF
13) (
1
).
•
Carefully detach the dummy module (
2
) from the base plate
module (
3
) and set it to one side along with the two screws
(
1
) and mounted packing rings (
6
).
•
If necessary, clean the flanging area of the base plate module
with a suitable (lint-free!) cleaning cloth.
NOTE
In the event that only one already mounted SMBM-X
module is to be replaced by a new SMBM-X module,
proceed with the mounting point "Replacement of an
SMBM-X module."
9.4.1.2 Initial installation of an SMBM-X module
•
Screw the plug screw (
4
) into the borehole (
5
) and tighten it
securely (conical thread).
•
Place a new O-ring (
6
) in the groove of the borehole (
7
).
•
Carefully place the SMBM-X module (
10
) on the flanging area
of the base plate module (
3
).
•
At the SMBM-X module, put the hexagon socket screw (
8
)
(M8 x 100, WAF 6) in place and tighten it slightly.
•
Also place the opposite-side hexagon socket screw (
9
) (M8 x
40, WAF 6) in place and tighten it slightly as well.
•
Tighten the two screws evenly crosswise with a torque of 15
± 1 Nm.
9.4.1.3 Replacement of an SMBM-X module
•
Place a new O-ring (
6
) in the groove of the borehole (
7
).
•
Carefully place the SMBM-X module (
10
) on the flanging area
of the base plate module (
3
).
•
At the SMBM-X module, put the hexagon socket screw (
8
)
(M8 x 100, WAF 6) in place and tighten it slightly.
•
Also place the opposite-side hexagon socket screw (
9
) (M8 x
40, WAF 6) in place and tighten it slightly as well.
•
Tighten the two screws evenly crosswise with a torque of 15
± 1 Nm.
•
If necessary, clean the flow limiter to remove any external
impurities.
•
Open the oil feed to the flow limiter.
Содержание SKF SMBM-V EEX
Страница 49: ...49 Fig 32 Mechanical connection options SMBM V...
Страница 61: ...61 Fig 40 Replacement of an SMBM module...
Страница 62: ...62 Fig 41 Expansion of an existing assembly to include an SMBM module...
Страница 73: ...73...
