Lincoln 2008 MKX Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 329

background image

Front safety belt pretensioners

The safety belt pretensioners at the front outboard seating positions are
designed to tighten the safety belts firmly against the occupant’s body
during frontal collisions, and in rollover and side collisions when the
Safety Canopy is activated. This helps increase the effectiveness of the
safety belts. In frontal collisions, the safety belt pretensioners can be
activated alone or, if the collision is of sufficient severity, together with
the front airbags.

Front safety belt energy management retractors

The front outboard safety belt energy management retractors allow
webbing to be pulled out of the retractor in a gradual and controlled
manner in response to the occupant’s forward momentum. This helps
reduce the risk of force-related injuries to the occupant’s chest by
limiting the load on the occupant. Refer to

Energy management feature

section in this chapter.

Determining if the Personal Safety System™ is operational

The Personal Safety System™ uses a warning light in the instrument
cluster or a back-up tone to indicate the condition of the system. Refer
to the

Warning light

section in the

Instrument Cluster

chapter.

Routine maintenance of the Personal Safety System™ is not required.

The Restraints Control Module (RCM) monitors its own internal circuits
and the circuits for the airbag supplemental restraints, crash sensor(s),
safety belt pretensioners, front safety belt buckle sensors, driver seat
position sensor, and front passenger sensing system. In addition, the
RCM also monitors the restraints warning light in the instrument cluster.
A difficulty with the system is indicated by one or more of the following.

•

The warning light will either flash or stay lit.

•

The warning light will not illuminate immediately after ignition is
turned on.

•

A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and warning light are repaired.

If any of these things happen, even intermittently, have the Personal
Safety System™ serviced at an authorized dealer immediately. Unless
serviced, the system may not function properly in the event of a
collision.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

144

«
...
143
144
145
146
147
...
»

Содержание 2008 MKX










































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 MKX

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: AMP Research Страницы: 12

Half Size Trunk Box Organizer C-TBO-CV

Бренд: Havis-Shields Страницы: 1

Бренд: Volvo Страницы: 8

2008 MX-5 Miata

Бренд: Mazda Страницы: 400

Бренд: Rola Страницы: 3

Бренд: AA Products Страницы: 6

Бренд: Fast Master Products Страницы: 13

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

Бренд: Sagem Страницы: 10

Бренд: TEINHOF Страницы: 2

2000 9-5 2.3 Turbo Ecopower

Бренд: Saab Страницы: 256

Бренд: rough country Страницы: 4

Бренд: Volvo Страницы: 197

Бренд: Prime Design Страницы: 8

Бренд: Edelbrock Страницы: 1

Бренд: ideus Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды