manualshive.com logo in svg

Lincoln 2008 MKX, Руководство пользователя

Владелец Lincoln 2008 MKX может легко загрузить руководство по эксплуатации бесплатно с веб-сайта manualshive.com. Откройте для себя полезные советы и инструкции по уходу за вашим автомобилем с помощью этого руководства. Наслаждайтесь безопасной и комфортной поездкой с вашим Lincoln 2008 MKX.

Поделиться
Скачать
background image

Low Tire
Pressure
Warning Light

Possible
cause

Customer Action Required

Flashing Warning
Light

Spare tire in
use

Your temporary spare tire is in
use. Repair the damaged road
wheel and re-mount it on the
vehicle to restore system
functionality. For a description of
how the system functions under
these conditions, refer to

When

your temporary spare tire is
installed

in this section.

TPMS
malfunction

If your tires are properly inflated
and your spare tire is not in use
and the TPMS warning light still
flashes, have the system inspected
by your authorized dealer.

When inflating your tires

When putting air into your tires (such as at a gas station or in your
garage), the Tire Pressure Monitoring System may not respond
immediately to the air added to your tires.

It may take up to two minutes of driving over 20 mph (32 km/h) for the
light to turn OFF after you have filled your tires to the recommended
inflation pressure.

How temperature affects your tire pressure

The Tire Pressure Monitoring System (TPMS) monitors tire pressure in
each pneumatic tire. While driving in a normal manner, a typical
passenger tire inflation pressure may increase approximately 2 to 4 psi
(14 to 28 kPa) from a cold start situation. If the vehicle is stationary
over night with the outside temperature significantly lower than the
daytime temperature, the tire pressure may decrease approximately 3 psi
(20.7 kPa) for a drop of 30° F (16.6°C) in ambient temperature. This
lower pressure value may be detected by the TPMS as being significantly
lower than the recommended inflation pressure and activate the TPMS
warning for low tire pressure. If the low tire pressure warning light is
ON, visually check each tire to verify that no tire is flat. (If one or more
tires are flat, repair as necessary.) Check air pressure in the road tires. If
any tire is under-inflated, carefully drive the vehicle to the nearest
location where air can be added to the tires. Inflate all the tires to the
recommended inflation pressure.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Tires, Wheels and Loading

204

Содержание 2008 MKX










































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 MKX

Daihatsu G200 Service Manual preview
G200
Бренд: Daihatsu Страницы: 485
Jeep Commander Overview Manual preview
Commander
Бренд: Jeep Страницы: 25
Jeep Commander Warranty Information Booklet preview
Commander
Бренд: Jeep Страницы: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Бренд: Farenheit Страницы: 8
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
PEUGEOT Partner Origin Handbook preview
Partner Origin
Бренд: PEUGEOT Страницы: 128
Schumacher Electric SPI6 Owner'S Manual preview
SPI6
Бренд: Schumacher Electric Страницы: 87
Cadillac 2009 ESCALADE ESV Owner'S Manual preview
2009 ESCALADE ESV
Бренд: Cadillac Страницы: 602
Chevrolet LUMINA 1997 Owner'S Manual preview
LUMINA 1997
Бренд: Chevrolet Страницы: 376
Mazda 2008 CX-9 Brochure & Specs preview
2008 CX-9
Бренд: Mazda Страницы: 15
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Бренд: DAF Страницы: 18
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
Porsche 01-B Web Application Manual preview
01-B
Бренд: Porsche Страницы: 313
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Бренд: Zap Страницы: 16
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
AllTrade Powerbuilt 648601 Operating Instructions preview
Powerbuilt 648601
Бренд: AllTrade Страницы: 3
Perrycraft SportQuest Series Installation preview
SportQuest Series
Бренд: Perrycraft Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды