Lincoln 2008 MKX Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 329

background image

Increasing the inflation pressure beyond this pressure will not increase
the tire’s load carrying capability.

•

kPa:

Kilopascal, a metric unit of air pressure.

•

PSI:

Pounds per square inch, a standard unit of air pressure.

•

Cold inflation pressure:

The tire pressure when the vehicle has

been stationary and out of direct sunlight for an hour or more and
prior to the vehicle being driven for 1 mile (1.6 km).

•

Recommended inflation pressure:

The cold inflation pressure found

on the Safety Compliance Certification Label or Tire Label located on
the B-Pillar or the edge of the driver’s door.

•

B-pillar:

The structural member at the side of the vehicle behind the

front door.

•

Bead area of the tire:

Area of the tire next to the rim.

•

Sidewall of the tire:

Area between the bead area and the tread.

•

Tread area of the tire:

Area of the perimeter of the tire that

contacts the road when mounted on the vehicle.

•

Rim:

The metal support (wheel) for a tire or a tire and tube assembly

upon which the tire beads are seated.

INFLATING YOUR TIRES

Safe operation of your vehicle requires that your tires are properly
inflated. Remember that a tire can lose up to half of its air pressure
without appearing flat.

Every day before you drive, check your tires. If one looks lower than the
others, use a tire gauge to check pressure of all tires and adjust if
required.

At least once a month and before long trips, inspect each tire and check
the tire pressure with a tire gauge (including spare, if equipped). Inflate
all tires to the inflation pressure recommended by Ford Motor Company.

Use a tire gauge to check the tire inflation pressure, including the spare
(if equipped), at least monthly and before long trips. You are strongly
urged to buy a reliable tire pressure gauge, as automatic service station
gauges may be inaccurate. Ford recommends the use of a digital or
dial-type tire pressure gauge rather than a stick-type tire pressure gauge.

Use the recommended cold inflation pressure for optimum tire
performance and wear. Under-inflation or over-inflation may cause
uneven treadwear patterns.

2008 MKX

(mkx)

Owners Guide (post-2002-fmt)
USA

(fus)

Tires, Wheels and Loading

188

«
...
187
188
189
190
191
...
»

Содержание 2008 MKX










































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 MKX

Бренд: GMC Страницы: 140

Бренд: Subaru Страницы: 3

Car Top Duffle Bag

Бренд: Rightline Gear Страницы: 2

Бренд: EEZ RV Страницы: 31

Бренд: Volvo Страницы: 211

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

Бренд: AIS Страницы: 2

Бренд: Honda Страницы: 124

2011 SRX CROSSOVER

Бренд: Cadillac Страницы: 416

Бренд: TIE DOWN Страницы: 2

Бренд: TrailFX Страницы: 2

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Бренд: Sintrones Страницы: 55

Бренд: Navman Страницы: 27

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Бренд: Ecco Страницы: 2

Бренд: Prorack Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды