Lika MTA1 Скачать руководство пользователя

Страница: 39 / 48

SMA1

Offset

Save and activate Preset / Offset

command

in the

Command

Preset / Offset structure:

Reg.

MSB

…

LSB

- 2

Use the

Save and activate Preset / Offset

function (set “02” in the register 48)

to store and activate the new value.
The max. allowed Preset value depends on the set resolution.
resolution = 0.1



max preset = 00 FF FFh (16 bits)

resolution = 0.05



max preset = 01 FF FFh (17 bits)

resolution = 0.01



max preset = 07 FF FFh (19 bits)

resolution = 0.005



max preset = 0F FF FFh (20 bits)

The Offset value must be less than or equal to the difference between the
overall position information (24 bits, see

Position

) and the max. position

information allowed by the set resolution (see the

Absolute resolution

00h

Device type

[55, ro]

This register describes the type of device.
Default =

06h

: linear encoder BiSS + SINE/COSINE signals.

SINE / COSINE resolution

[58, ro]

This register describes the period of the sine/cosine signal.
Default =

01h

: resolution = 1mm

Device ID

[78 … 7D, ro]

These registers show the Device ID, hexadecimal values are according to ASCII
code.

Reg.

Hex

ASCII

xx: software version

MAN SMA1 E 2.9.odt

7 - BiSS C-mode interface

39 of 48

Содержание MTA1

















































Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды

Lika MTA1, Руководство пользователя

Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды