Lika MTA1 Скачать руководство пользователя | Manualshive

Страница: 24 / 48

background image

SMA1

Serial number

[44 … 47, ro]

These registers show the serial number of the device expressed in hexadecimal
notation.
Register 44

: year of production

Register 45

: week of production

Registers 46 and 47

: serial number in ascending order

Command

[48, wo]

Value

Function

00

Normal operation

01

Save parameters on EEPROM

02

Save and activate Preset / Offset

04

Load and save default parameters

After having set a new value in some register, use the

Save parameters on

function in this register to store it. Set “01” in the register.

After having set a Preset / Offset value, use the

Save and activate Preset /

function in this register to both store and activate the preset / offset at

the same time. Set “02” in the register.

Load and save default parameters

: default parameters are set at the factory

by Lika Electronic engineers to allow the operator to run the device for standard
operation in a safe mode. As soon as the command is sent the default
parameters are uploaded and activated. All parameters which have been set
previously are overwritten, thus previously set values are lost. The complete list
of machine data and the relevant default parameters preset by Lika Electronic
engineers are available on page 46. Set “04” in the register.

WARNING

As soon as the

Load and save default parameters

command is sent, all

parameters which have been set previously are overwritten, thus previously set
values are lost!

As soon as the command is sent, the register is set back to "00" (

) automatically.

Wait min. 30 ms (EPROM writing time) before using a new function.
Default = 00 (

Normal operation

MAN SMA1 E 2.9.odt

6 - BiSS B-mode interface

24 of 48

«
...
22
23
24
25
26
...
»

Содержание MTA1

















































Отзывы:

Нет отзывов

Похожие инструкции для MTA1

Бренд: B&B Electronics Страницы: 2

Бренд: hc-cargo Страницы: 38

EnerSolis ES3000T

Бренд: Ablerex Страницы: 25

Бренд: B&K Страницы: 2

Varispeed CIMR-G7A

Бренд: YASKAWA Страницы: 459

Бренд: tams elektronik Страницы: 26

Multimedia Enclosure ME3

Бренд: Emprex Страницы: 40

Бренд: IONODES Страницы: 23

PowerVerter Plus PV 1000FC

Бренд: Tripp Lite Страницы: 20

Prizm 200750 Series

Бренд: Moog Страницы: 12

Бренд: Thunder Scientific Страницы: 164

Бренд: RDZ Страницы: 60

Бренд: Caliber Страницы: 52

Бренд: Emergi-Lite Страницы: 12

Бренд: Tektronix Страницы: 286

Бренд: GREISINGER Страницы: 2

Бренд: Quickfilter Страницы: 9

5.1 AV Switch Box

Бренд: Jaton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды