Licht-Technik Motoryoke BigBee MB-D1 Скачать руководство пользователя страница 31

Страница: 31 / 52

P11 PAN-axis moving range

At this point the

PAN-axis moving range

can be programmed. The moving range has as

reference point the PAN-axis middle position which can be set in P05,

PAN-axis middle

position, page 29

. For example: If this menu is programmed to 90°, the motoryoke moves

90° to the left

and

90° to right from middle position.

Before programming this point read chapter

PAN-axis moving range, page 20

and

P05

PAN-axis middle position, page 29

Range of values:

10..182 degrees

Recommended value:

45°

Operation:

depress You are now on menu level. The last adjusted menu
point is displayed, e.g.:

Menu P01: DMX address motoryoke

depress ... until

Menu P11

is displayed

depress The second line displays the currently adjusted value.

depress Adjust the desired moving range

depress You are back on menu level.

depress The equipment is ready for operation.

Caution !!

Check the

entire moving

range of the lamp:

The lamp-manufacturer specify

minimum distances

to inflammable materials. Never fall

below the minimum distance in no position of the lamp!

Make sure that no cable will be

broken

bended

stretched

damaged

anyhow by

reason of turning the motoryoke!

Motoryoke MB D1 V4.56 Rev 1.06 31

Menü

Содержание Motoryoke BigBee MB-D1





















































Результаты поиска

Содержание Motoryoke BigBee MB-D1

Отзывы:

Похожие инструкции для Motoryoke BigBee MB-D1

Бренды по названию

Популярные бренды

Licht-Technik Motoryoke BigBee MB-D1, Функциональное описание

Результаты поиска

Содержание Motoryoke BigBee MB-D1

Отзывы:

Похожие инструкции для Motoryoke BigBee MB-D1

Бренды по названию

Популярные бренды