LG Therma V ZHBW056A0 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 115

LG Therma V ZHBW056A0 Скачать руководство пользователя страница 76

- 76 -

Copyright © 2018 LG Electronics Inc. All rights reserved.
Only training and service purposes.

Check Point

1. Unplug the sensor on PCB(Heater).
2. Estimate the resistance of each sensor.
3. If the resistance of the sensor is 5 KΩ at 25°C, then sensor is normal.
4. If the resistance of the sensor is 0 KΩ or ∞, then sensor is abnormal.

’

Change the sensor.

5. Plug the sensor on PCB(Heater) and Power ON.
6. Estimate the voltage of each sensor.
7. If the voltage of the sensor is 2.5Vdc at 25°C, then sensor is normal.
8. If the resistance of the sensor is 0 or 5Vdc, then sensor is abnormal.

’

Repair or Change the PCB.

5k

Unplugged

Plugged

Check the resistance

Check the voltage

V

2.5Vdc

Unplug the sensor

on PCB(Heater)

Estimate the Voltage

of each sensor.

Is the voltage of

the sensor 2.5 V dc

at 25 ˚C

Repair or Change the PCB.

Check the

Connector connection

Is it normal ?

Estimate the resistance

of each sensor.

Plug the sensor

on PCB(Heater)

Is the resistance of

the sensor

5 k at 25 ˚C?

Yes

Yes

No
Correct connection

Yes

No
Correct connection

No
Correct connection

Check Flow Chart

Display

code

Title

Cause of error

Check point & Normal condition

08

Problem in

Water Tank

sensor

• Connector connection error
• Faulty PCB(Heater)
• Faulty sensor (Open / Short)

Normal resistor : 5 KΩ / at 25 ˚C (Unplugged)
Normal voltage : 2.5 V dc / at 25 ˚C (Plugged)
Refer to sensor resistance table.

13

Problem in

Solar-thermal

sensor

• Connector connection error
• Faulty PCB(Heater)
• Faulty sensor (Open / Short)

Normal resistor : 5 KΩ / at 25 ˚C (Unplugged)
Normal voltage : 2.5 V dc / at 25 ˚C (Plugged)
Refer to sensor resistance table

«
...
74
75
76
77
78
...
»

Содержание Therma V ZHBW056A0




















































































































Отзывы:

Нет отзывов