LG GoldStar MS-106YG страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 35

background image

5-9

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
CAPACITOR

HIGH VOLTAGE
DIODE

NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction.

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to terminal.

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to case.

Measure the continuity (Forward).
(Ohm-meter scale: Rx10000)

Measure the continuity (Reverse).
(Ohm-meter scale: Rx10000)

Normal: Momentarily indicates

several ohms, and
then gradually returns
to infinite.

Normal: Infinite.

Normal: Continuity.
Abnormal: Infinite.

Normal: Infinite.
Abnormal: Continuity.

NOTE: When testing the magnetron, be sure to install the magnetron gasket

in the correct position and be sure that the gasket is in good condition.

Antenna

Gasket

Chassis

Filament

«
...
17
18
19
20
21
...
»

Содержание GoldStar MS-106YG




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-106YG

Бренд: Jenn-Air Страницы: 4

Бренд: Logik Страницы: 32

Бренд: Motak Страницы: 16

Бренд: Scarlett Страницы: 31

Бренд: Baumatic Страницы: 24

7170 052? 7172 042

Бренд: Foster Страницы: 18

Бренд: PROFILO Страницы: 24

Бренд: Daewoo Страницы: 27

Бренд: Daewoo Страницы: 12

Бренд: Nordson Страницы: 166

Бренд: Fargas Страницы: 27

Бренд: Panasonic Страницы: 39

Бренд: Panasonic Страницы: 39

Бренд: Samsung Страницы: 56

Бренд: Daewoo Страницы: 10

Бренд: GE Страницы: 2

Competence 3121 B

Бренд: AEG Страницы: 32

COMPETENCE 5151 B

Бренд: AEG Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды