LG GoldStar MS-106YG страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 35

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 0.2 ~ 0.4 ohm
Approx.: 60 ~ 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

FILAMENT
WINDING

PRIMARY
TERMINAL

COMPONENT TEST PROCEDURE

«
...
16
17
18
19
20
...
»

Содержание GoldStar MS-106YG




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-106YG

Бренд: Samsung Страницы: 120

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 3

Бренд: Samsung Страницы: 32

Profile Advantium PSA2200R

Бренд: GE Страницы: 80

Profile Advantium PSB9240DFBB

Бренд: GE Страницы: 3

Бренд: GE Страницы: 40

SpacemakerXL JVM1631

Бренд: GE Страницы: 40

Бренд: NEFF Страницы: 32

Бренд: Oster Страницы: 17

Бренд: Bompani Страницы: 84

Бренд: Garland Страницы: 20

Бренд: GE Страницы: 2

24" MCD2661EM MicroMat-Duo

Бренд: AEG Electrolux Страницы: 46

Бренд: Kambrook Страницы: 20

Бренд: Denka Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды