LG GoldStar MS-106YG страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 35

background image

5-4

D. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB ASS’Y to

the control panel.

3) Disconnect the flat cable from the PCB SUB

ASS’Y and take off the PCB SUB ASS’Y

E. DOOR MAIN ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover very carefully with a flat-blade

screwdriver.

CAUTION: Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:

1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 4 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

Key Membrane

Door Open Button

Release
Lever

Button Spring

Control Panel

PCB Sub Asm

Remove door

Remove choke cover

Spacer

«
...
12
13
14
15
16
...
»

Содержание GoldStar MS-106YG




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-106YG

Бренд: Oster Страницы: 16

Бренд: Blanco Страницы: 24

Бренд: GE Страницы: 32

Бренд: DAEWOO ELECTRONICS Страницы: 22

Бренд: Magic Chef Страницы: 24

Бренд: Scarlett Страницы: 32

Бренд: Orbegozo Страницы: 32

Бренд: NEFF Страницы: 36

Бренд: Blanco Страницы: 28

Бренд: John Lewis Страницы: 48

DEC1000VP series

Бренд: Menumaster Страницы: 212

Бренд: Daewoo Страницы: 15

Бренд: Cafe Страницы: 52

Бренд: Hotpoint Ariston Страницы: 60

Бренд: Kuppersbusch Страницы: 23

7170 052? 7172 042

Бренд: Foster Страницы: 18

Бренд: Thermador Страницы: 20

Бренд: zesto Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды