manualshive.com logo in svg

LG ARNH963K2A2, Руководство по установке

Поделиться
Скачать
LG ARNH963K2A2 Скачать руководство пользователя страница 37

Accessories Installation   

Hydro Kit

Installation Manual 

37

ENGLISH

How to wire Independent Power Module

Step 1. Turn the power off using circuit breaker.

Step 2. Disconnect the EEV cable of the indoor units PCB(CN-EEV)

Step 3. Connect the independent power kit(CN-EEV/LOAD) to the indoor units EEV, using harness 1.

Step 4. Connect the independent power kit(CN-EEV/MAIN) to the indoor units PCB(CN-EEV/CN-

WRITE), using harness 2.

Step 5. Supply the power.

WARNING: 

• The wire should not be exposed to the outside otherwise it may leads to the malfunction of

the independent power kit due to wire damage.

• Wrong wiring also causes the malfunction of the independent power kit or damage to it.
• Power should be supplied more than 20 minutes continuously in order to operate the

independent power kit correctly. Otherwise, the independent power kit can not fully close the
EEV due to the lack of the charging power.

For more detailed information, refer to the installation manual of Independent Power
Module.

To Indoor unit’s EEV

EEV

CN_EEV/MAIN

CN_EEV/LOAD

Harness 1

Harness 1

Harness 1

CN-EEV

CN-WRITE

Harness 2

Harness 2

Harness 2

Содержание ARNH963K2A2
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды