manualshive.com logo in svg

LG ARNH963K2A2, Руководство по установке

Поделиться
Скачать
LG ARNH963K2A2 Скачать руководство пользователя страница 24

Accessories Installation

24

Hydro Kit

Location of Accessories and External Parts Connection

3WAY VALVE

(B)

WATER

PUMP

Not used

(B)

3WAY VALVE

(A)

1

L

BR

WH

BL

BR

BL

BR

WH      BL

2

L1

3

N

4

L

5

N

6

7

8

L

9

L1

10

N

PUMP

(A)

2WAY VALVE

(A)

THERMOSTAT

(Default : 230V AC)

11

L

BR

12

N

BL

13

14
L1

BR

15
L2

WH

16

N

BL

17

L

BR

18

N

BL

19
L1

WH

20
L2

BK

Dry contact board attachment location

Dry contact board socket. (CN-CC)

Water tank temperature sensor socket. (CN-TH4)

Remote controller socket. (CN-REMO)

• Connect 3way valve, if both floor heating and hot water is used.
• Connect the separately purchased thermostat.
• Dry contact is an accessory supplied by LG and installed by referring to installation manual.
• 3way valve, thermostat and pump are external parts for installation, which are not supplied by LG.

After checking each part carefully, install external parts respectively.

• Connect the cable of each accessory to the terminal block of the control box in the 

Hydro Kit

.

• Check the label attached on the terminal block to prevent wrong connection.
• Use the pump of 220 voltage and maximum operation current of 4A or less.
• Select a suitable relay for pump capacity when connecting the pump to the unit.

WARNING: 

Install the unit after turning off the main power.
Do not attempt to operate the Hydro Kit outside the operational parameters set forth in this
manual and the product specifications.
Do not work with wet hand.

5. Accessories Installation

Содержание ARNH963K2A2
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды