Lexmark E360D series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 166

background image

Diagnostic aids

3-3

4513-420, -430

Reset photoconductor maintenance counter (Reset PC Cnt)

The reset photoconductor maintenance counter resets the photoconductor kit page counter and clears any
warnings or photoconductor exhausted messages. This operation should be performed only after a new
photoconductor unit has been installed.

Print quality pages (Prt Quality Pgs)

The print quality test pages can be printed from either the Diagnostics menu or Configuration Menu (CONFIG
MENU). When printed from the Diagnostic mode, additional information is included, and the print cartridge
lockout is bypassed. See

“Print quality pages (Prt Quality Pgs)” on page 3-3

. Additional configuration

information may be included on the print quality pages which is not included on the print menu page.

To print the Print Quality Test Pages, select

Prt Quality Pgs

from CONFIG MENU. The message

Printing

Quality Test Pages

is displayed.

The print quality test consists of four pages. Page one contains device information, cartridge information, margin
settings, minimum stroke width, and a mixture of graphics and text. Page two is a gray page containing two
graphics, page three is black, and page four is blank. If the duplex is turned on, then the pages are duplexed.
The Print Quality Test pages are printed in English and must always be printed on letter, legal, or A4 paper.

Reports

The Reports menu contains two selections: Menu Settings Page and Event Log.

Menu Settings Page

The Menu Settings Page contains information...

To print the Menu Settings page, press

. Press

to return to the Configuration menu.

Event Log

The event log provides a history of printer errors. The event log can be printed only in the Configuration
menu. Additional options are available in the Diagnostics menu. See

“Event log” on page 3-14

.

To print the event log:

1.

Select

Print Event Log

from the Event Log menu.

2.

Press

to return to the Configuration menu.

Note:

An event log printed from the CONFIG MENU will not contain debug information or secondary

codes for 900 service errors. However, the event log printed from DIAGNOSTICS mode does include this
information.

Panel Menus

The settings are

On

and

Off

. The default is

On

.

PPDS Emulation

This menu item activates or deactivates PPDS emulation data stream. The selections are

Deactivate

(default)

and

Activate

. When PPDS emulation is activated, the following settings are also changed:

•

SmartSwitch settings for each port are turned off.

•

The printer language is changed to PPDS Emulation.

Users can still switch languages on the operator panel and through the PJL data stream.

«
...
61
62
63
64
65
...
»

Содержание E360D series







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E360D series

Бренд: Oki Страницы: 2

Бренд: Xerox Страницы: 25

Бренд: EBS Страницы: 34

Бренд: Oki Страницы: 268

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 202

Бренд: Oki Страницы: 201

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 616

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 138

Microline 320 Turbo D1

Бренд: Oki Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды