Lexmark E360D series Скачать руководство пользователя страница 30

Страница: 30 / 166

2-4

Lexmark™ E360d, E360dn

4513-420, -430

Display

The display shows messages describing the current state of the printer and indicating
possible printer problems that must be resolved.

The top line of the display is the header line. It will display the current status and the
Supplies (Warnings) status. This is where printer status, supplies messages, and
show-me screens are viewed.

Indicator light

The indicator light indicates printer status.

• If the light is off, then the printer power is off.
• If the light is blinking green, then the printer is warming up, processing date, or

printing.

• If the light is solid green, then the printer is on, but idle.
• If the light is blinking red, then operator panel intervention is needed.

Button or control panel item

Function

Содержание E360D series







































































































































































Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды

Lexmark E360D series, Руководство по обслуживанию

Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды