Lexmark E360D series Скачать руководство пользователя страница 61

Страница: 61 / 166

Diagnostic aids

3-1

4513-420, -430

3. Diagnostic aids

Accessing service menus

There are two different test menus that can be accessed during POR to identify problems with the printer.

Printing menus

To print a listing of the states and settings of the printer:

At the

Ready

prompt, press

under

Menu

until

Utilities

appears.

Press .

Press

until

Print Menus

appears.

Press .

Configuration Menu

1. Turn off the printer.
2. Press and hold

and

3. Turn on the printer.
4. Release the buttons when

Performing

Self Test

displays.

5. The message

CONFIG MENU

displays on

the top line of the operator panel.

The Configuration menu group contains a set
of menus, settings, and operations which are
infrequently required by a user. Generally, the
options made available in this menu group are
used to configure a printer for operation.

See

“Available menus” on page 3-2

Diagnostics Mode

1. Turn off the printer.
2. Press and hold

and

3. Turn on the printer.
4. Release the buttons when

Performing

Self Test

displays.

The Diagnostic menu group contains the
settings and operations used while
manufacturing and servicing the printer.

See

“Menus may vary depending on the

features and options of the printer.” on
page 3-5

Содержание E360D series







































































































































































Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды

Lexmark E360D series, Руководство по обслуживанию

Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды