Lexmark E360D series Скачать руководство пользователя страница 27

Страница: 27 / 166

Diagnostics information

2-1

4513-420, -430

2. Diagnostics information

Start

CAUTION:

Unplug power from the printer before connecting or disconnecting any cable,

assembly, or electronic card. This is a precaution for personal safety and to prevent damage to the
printer.

This chapter contains the codes and diagnostic tools to aid in providing corrective action for a malfunctioning
printer. To determine the corrective action to repair a printer, look for the following information:

•

A description of a problem, see

“Symptom tables” on page 2-16

•

Information from the operator panel of the printer.

—

Models E360d and E360dn

have an operator panel with messages. See

“Overview of the

operator panel and menus” on page 2-2

Power—On Self Test (POST) sequence

The following is an example of the events that occur during the POR sequence when the printer is turned on.

Diamonds are displayed on the operator panel.

While code is being loaded into DRAM, dots scroll across the operator panel.

A screen is displayed with the memory and processor speed. A typical example of this message is:

Performing Self Test

is displayed.

Busy

is displayed.

Close Door

will be displayed if the cover is open.

Any cartridge errors, such as

Defective Cartridge

, are displayed.

Applicable maintenance messages are displayed.

Applicable toner low messages are displayed.

10.

The printer displays

Ready

32 Mb

366 Mhz

Menus

Back

Stop

Содержание E360D series







































































































































































Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды

Lexmark E360D series, Руководство по обслуживанию

Результаты поиска

Содержание E360D series

Отзывы:

Похожие инструкции для E360D series

Бренды по названию

Популярные бренды