•
A 7/8 inch hole cut on the hinged side of the enclosure is recommended
for the Remote Supervisor Panel connections. See Remote Supervisor
Panel instructions for its connection method.
9. Battery Installation:
A 9-Volt alkaline battery is included in the shipping
carton. The purpose of the 9-Volt battery is to power the diagnostic warning
circuitry in the event of a power failure or multiple fuse failures. Remove the
battery holder from the diagnostic assembly. Insert the 9-Volt battery (be
sure to follow the polarity markings on the battery compartment), and slide
the battery holder back in.
10. Secure modules
and replace terminal block cover.
Be certain all TVSS
Modules are tightly in place and remove any extra materials. Close and
secure enclosure cover door before applying power.
11. Activate the system by turning AC power ON:
The 6 Green Module
Status lights should be illuminated and visible through the ports in the
enclosure door, and all other lights should be OFF. If problems are
encountered that can not be resolved using the Problem Isolation
Procedure printed on the inside of the enclosure door, contact Leviton
Technical Support: 1-800-648-3332.
12. Diagnostic Test:
Press and hold down the test button. The Red warning
indicator should blink, the audible tone signal should beep, the Yellow low
battery light should illuminate, and the Remote Supervisor Panel warning
indicator, if wired in, will be activated. Release the test button.
13. Surge Counter Test:
If the 57000 Panel has a LCD surge counter on it's
front panel, press it's "Reset" switch, then the "Test" switch. The display
should register surge counts each time the "Test" switch is depressed. The
"Reset" switch should be depressed whenever the LCD display is at a
maximum (the LCD unit's red LED will be illuminated). "Reset" may be
depressed anytime to clear the display.
SERVICING INSTRUCTIONS
Leviton Series 57000 TVSS Servicing Instruction Procedure:
Carefully
read these instructions as well as the Module and Fuse Replacement
Instruction Procedure before attempting service.
CAUTION:
BEFORE OPENING TVSS ENCLOSURE COVER, POWER
MUST BE TURNED OFF. ELECTROCUTION AND FATAL OR SERIOUS
INJURY AND PROPERTY DAMAGE CAN RESULT FROM FAULTY
SERVICING. IT IS RECOMMENDED THAT THE 57000 TVSS PANEL
PROTECTION SYSTEM BE SERVICED BY A QUALIFIED ELECTRICIAN.
Page 8
Page 27
3. Identifique el sistema eléctrico en uso (Sistema de voltaje Delta o
Estrella):
¡Es crítico que coincidan los módulos DPS y los voltajes de línea!
Identifique el sistema en uso al medir los voltajes L-N y L-L.
PRECAUCIÓN:
¡LAS MEDICIONES DE VOLTAJE PUEDEN SER
PELIGROSAS PARA LA VIDA Y/O PROPIEDAD!
Confirme que los
voltajes MÁXIMOS medidos
NO
excedan los voltajes de CA especificados
en los Módulos de Reemplazo 57000, o pueden ocurrir daños a en los
módulos.
Vea las Figuras 1-3.
4. Monte firmemente:
Consulte las instrucciones de “Montaje de Panel”
incluidas.
G
L3
L1
N
L2
TVSS
Módulo 3
G
V(L-L)
L1
L3
V(L-L)
Módulo 2
Módulo 1
L2
V(L-L)
Fig. 2 - Tres Fases, 3 Hilos, Delta (No Aterrizado)
G
L3
L1
N
L2
TVSS
Módulo 3
Módulo de
Modo Común
G
V(L-L)
L1
L3
N
V(L-N)
V(L-N)
Módulo 2
Módulo 1
L2
V(L-N)
Fig. 1 - Tres fases, 4 Hilos con Tierra, Sistema en Estrella
DI-031-57000-20A
8/25/03, 4:24 PM
11