background image

Page 5

Installation & Operation Guide

Installation & Operation Guide

Page 18

120/240 or 120/200 80A

INPUT WIRING

The 2408 CD/CR must be provided with an 80 amp, 

120/240 or 120/208Y VAC, three wire electrical service. 

This service must include two live wires not exceeding 150 

volts to ground and one neutral wire. In addition the unit must 

be grounded by conduit or an additional ground wire in accordance 

with electrical codes.

The input wiring should be #4 AWG THWN or equivalent copper 

wire rated for least 75 C. 

Pass the input wiring through the 1 1/4” conduit hole in the top 

of the unit. Allow the wires to drop 4-6” into the unit then loop 

the wires back upwards. Connect each of the two live wires to the 

copper lugs located above the circuit breakers and connect the 

neutral wire to the neutral bar. If provided, connect the additional 

ground wire to the terminal marked “GND”.

20 AMP CIRCUIT BREAKERS

20 AMP CIRCUIT BREAKERS

LIMITED 2 YEAR WARRANTY AND 

EXCLUSIONS

WARRAN

TY

TRADEMARK DISCLAIMER

Use herein of third party trademarks, service marks, trade names, brand 
names and/or product names are for informational purposes only, are/may 
be the trademarks of their respective owners; such use is not meant to imply 
affiliation, sponsorship, or endorsement.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should 
contact Leviton in writing at Leviton Manufacturing of Canada Ltd to 
the attention of the Quality Assurance Department, 165 Hymus 
Blvd,  Pointe-Claire  (Quebec),  Canada  H9R  1E9
 or by telephone at  
1 800 405-5320.

Figure 2

INPUT WIRING

LOADS MAY EXIT TOP

20 AMP

CIRCUIT BRKRS

20 AMP

CIRCUIT BRKRS

GND

NEUTRAL BUS

Leviton warrants to the original consumer purchaser and not for the benefit 
of anyone else that this product at the time of its sale by Leviton is free 
of defects in materials and workmanship under normal and proper use for 
two years from the purchase date. Leviton’s only obligation is to correct 
such defects by repair or replacement, at its option.

 

For details visit 

www.leviton.com or call 1-800-824-3005.

 

This warranty excludes 

and there is disclaimed liability for labor for removal of this product or 
reinstallation. This warranty is void if this product is installed improperly or in 
an improper environment, overloaded, misused, opened, abused, or altered 
in any manner, or is not used under normal operating conditions or not in 
accordance with any labels or instructions.

 

There are no other or implied 

warranties  of  any  kind,  including  merchantability  and  fitness  for 
a particular purpose,

 

but if any implied warranty is required by the 

applicable jurisdiction, the duration of any such implied warranty, including 
merchantability and fitness for a particular purpose, is limited to two years.

 

Leviton is not liable for incidental, indirect, special, or consequential 
damages, including without limitation, damage to, or loss of use of, 
any equipment, lost sales or profits or delay or failure to perform 
this warranty obligation.

 

The remedies provided herein are the exclusive 

remedies under this warranty, whether based on contract, tort or otherwise.

Содержание 2408CD













Отзывы: