Let's Go Aero T01991 Скачать руководство пользователя страница 8

Страница: 8 / 10

STEP 5:

Insert the Thick Awning Poles

[R]

first into the eyelets at the corners of the Awning [Fg. 27], set opposite ends on the

ground and stake the tie-offs into the ground to secure awning [Fg. 26], or place the ends through the holes in the license
plate bracket and secure tie-offs to the jack stabilizer underneath the trailer [Fg. 29-30].

NOTE:

An optional carabiner clip is also included for easy connection to the Levelers and Stakes.

TIE-OFFS

[Fg. 26]

[Fg. 29]

[Fg. 27]

[Fg. 30]

STEP 4:

Insert the Thin Awning Poles

[Q]

(2) into the sleeves on

the underside of the Awning and insert the pole ends into
the corner pockets to secure. [Fg. 24]

NOTE:

Due to the tight fit, it may be easier to raise the

Thin Awning Poles

[Q]

“upside-down” and then “pop” the

poles upright. [Fg. 25]

THIN AWNING POLE

[Fg. 24]

[Fg. 25]

STEP 3:

Complete the attachment of Tent

[P]

by attaching the

remaining Velcro locations in the following order:

-Upper Sides (inside of the trailer)
-Lower Sides (outside of the trailer)
-U-Tube Door Panel
[Fg. 23]

UPPER SIDE

LOWER SIDE

U-TUBE/DOOR PANEL

[Fg. 23]

SHOWN WITHOUT

ENDGATE FOR CLARITY

Page 8 of 10

Содержание T01991











Результаты поиска

Содержание T01991

Отзывы:

Бренды по названию

Популярные бренды

Let's Go Aero T01991, Руководство пользователя

Результаты поиска

Содержание T01991

Отзывы:

Бренды по названию

Популярные бренды