background image

 Let’s Go Aero Warranty/Repair Procedures

Let’s Go Aero offers a 1 year limited warranty to each new Let’s Go Aero trailer against manufacturing defects in work-

manship and materials.
The obligation under this warranty is limited to the replacement or repair at the manufacturer’s factory, or at a point des-

ignated by the manufacturer, of such part as shall appear to the manufacturer upon inspection of such part to have been 

defective in material or workmanship. This warranty does not obligate Let’s Go Aero to bear the cost of labor or transpor-

tation charges in connection with the replacement or repair of defective parts, nor shall it apply to a product upon which 

alterations have been made or for equipment misused, neglected or improperly installed.
Let’s Go Aero reserves the right to improve any product through changes in design or materials as it may deem desirable 

without being obligated to incorporate such changes in products of previous manufacture.
Bills for service, labor, or other expenses which have been incurred by the buyer without express approval or authorization 

by Let’s Go Aero will not be accepted.
If your trailer fails to operate properly, or fails within the warranty period, the following steps should be taken:

1.  An RMA is required for any return of product for warranty work of defective components. Contact Let’s Go Aero 

for an RMA, toll free 877-464-2376, toll 719-630-3800, or via email to [email protected]. Freight must be 

prepaid – collect shipments will be refused. Include your RMA number, name, return address, phone number and a 

description of the problem. A copy of the receipt including date of purchase is necessary for any warranty claim.

2.  If damages are due to abuse or misuse, owner will be charged for parts and labor.
3.  If any of the components of your trailer are found to be faulty due to defective material or workmanship, they will 

be repaired at no charge and returned with transportation charges prepaid. If failure occurred because of abuse, 

neglect or misuse, an estimate of cost to repair will be submitted back to the owner. After repairs are completed, 

the material will be returned with transportation charges collect.

Any modifications made to the trailer or parts of the trailer will void the trailer warranty and release Let’s Go Aero of any 

responsibility for damages, injuries or accidents incurred.
For further information and customer assistance, call toll free, 1-877-464-2376 or 719-630-3800. 

Tuning Tips

If you will be using your LittleGiant Trailer™ for light loads (under 750 lbs), the 30 psi recommended tire pressure can be 

reduced to 22 psi to further enhance the trailer’s soft ride.

Trailer Licensing Notice

Some states may consider this trailer a vehicle requiring registration, licensing, and titling. In many states, you will need 

the Manufacturers Certificate of Origin filled out and signed by the dealer transferring ownership to you (the reseller from 

whom you purchased this trailer). Take this M.C.O. along with your bill of sale (cash register receipt) to your local DMV. 

Once you pay the appropriate fees, you will be issued a title or registration and license plate. Some states may require in-

spection of the assembled trailer before issuing a title, registration, or license. Check with your State Department of Motor 

Vehicles for information and guidance on registering, licensing, and titling the trailer.

  

Motor Vehicle law requires that the reseller sign over the Manufacturer’s Certificate of Origin 

 

to the buyer. The reseller is the dealer from whom the trailer was purchased by the buyer.  

 

Please contact your dealer for assistance in obtaining your M.C.O from them.  

© Copyright 2007 Let’s Go Aero, Inc.

Page 21 of 21

Содержание LittleGiant Trailer TLK864






















Отзывы: