Lenovo ThinkAgile HX2320 Appliance Скачать руководство пользователя страница 26

Страница: 26 / 100

•

Trusted Platform Module

System board LEDs

The illustration in this section shows the LEDs on the system board.

Figure 11. System board LEDs

System power LED

Heartbeat LED

System error LED

System ID LED

DIMM error LEDs

System fan 1 error LED

System fan 2 error LED

System fan 3 error LED

System fan 4 error LED

System fan 5 error LED

System fan 6 error LED

System fan 7 error LED

Parts list

Use the parts list to identify each of the components that are available for your server.

For more information about ordering the parts shown in Figure 12 “Server components” on page 23:

ThinkAgile HX2320 (7X83)

User Guide for ThinkAgile HX2320 Appliance and HX2321 Node

Содержание ThinkAgile HX2320 Appliance





































































































Результаты поиска

Содержание ThinkAgile HX2320 Appliance

Отзывы:

Похожие инструкции для ThinkAgile HX2320 Appliance

Бренды по названию

Популярные бренды

Lenovo ThinkAgile HX2320 Appliance, Руководство пользователя

Результаты поиска

Содержание ThinkAgile HX2320 Appliance

Отзывы:

Похожие инструкции для ThinkAgile HX2320 Appliance

Бренды по названию

Популярные бренды