Lenovo RackSwitch G7052 Скачать руководство пользователя страница 86

Страница: 86 / 86

G7052 Installation Guide

Power Specifications

The power specifications for the G7052 are listed in the following table.

Switching Performance

The feature performance characteristics of the G7052 are listed in the following

table.

Note:

The specific features supported on your switch, as well as some capacity

and performance characteristics, depend on the specific firmware installed.

For more information, see the

Application Guide

and

Command Reference

for your specific switch and its installed firmware.

Table 13. G7052 AC power specifications

Specification

Measurement

Number of power supplies

AC-input frequency (universal)

50–60 Hz

AC-input voltage (universal)

100–240 VAC

AC inrush current

30 A (RMS) @ 115 VAC/60 Hz

60 A (RMS) @ 230 VAC/50 Hz

AC-input current (typical)

0.61 A (RMS) @ 120 VAC/60 Hz

0.33 A (RMS) @ 230 VAC/50 Hz

AC-input current (maximum)

0.71 A (RMS) @ 120 VAC/60 Hz

0.37 A (RMS) @ 230 VAC/50 Hz

Power supply rated output power

102 W

System power dissipation (typical)

76 VA

System power dissipation (maximum)

85 VA

Table 14. G7052 feature performance characteristics

Feature

Characteristics

Switching architecture

Dual fabric

Throughput

176 Gbps full-duplex

Ethernet line rate

100%

IEEE 802.1Q VLANs

512, with 4K VLAN IDs

Forwarding database entries

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды