Lenovo RackSwitch G7052 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 86

background image

© Copyright Lenovo 2015

Chapter 2: Switch Components

25

Rear Panel

Fans

Three internal fans cool the switch unit. If an individual fan fails, the other fans

continue to run, and the switch unit continues to operate normally.

Note:

Fans are not customer replaceable.

Fan operation and internal temperatures are monitored. If the air temperature

exceeds a desired threshold, the environmental monitor displays warnings.

Note:

If a fan fails, the maximum operating temperature drops from +40°C (104°F)

to +35°C (95°F).

If there is a failure of one or more fans, the front panel Fan LED flashes.

Power Supply

The rear panel of the G7052 has two power connectors. The IEC 320 power

connector is for primary AC power when attached to a universal grounded AC power

source. The DC power connector supports an external DC redundant power supply

that can be purchased separately

.

Compatible power options are listed in the

Lenovo Networking Catalog

.

Statement 5

CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.

1

2

«
...
23
24
25
26
27
...
»

Содержание RackSwitch G7052























































































Отзывы:

Нет отзывов

Похожие инструкции для RackSwitch G7052

TRIPP LITE Series

Бренд: Eaton Страницы: 8

Бренд: Zamel Страницы: 2

ToolBox GTB-MHDMI1.3-441

Бренд: Gefen Страницы: 25

Бренд: PRO SIGNAL Страницы: 4

Бренд: Scion Страницы: 8

Бренд: Wyrestorm Страницы: 4

Бренд: ATEN Страницы: 4

Бренд: Edge-Core Страницы: 65

Бренд: Gembird Страницы: 11

Бренд: Aruba Networks Страницы: 40

Бренд: Campbell Страницы: 10

Бренд: Pakedge Device & Software Страницы: 8

Бренд: Black Box Страницы: 2

Бренд: iNels Страницы: 4

Бренд: JUKI Страницы: 2

Бренд: Bircher Reglomat Страницы: 4

Бренд: Exsys Страницы: 14

Бренд: Edge-Core Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды