Lenovo RackSwitch G7052 Скачать руководство пользователя страница 15

Страница: 15 / 86

Chapter 1. The RackSwitch G7052

Introduction

This

Installation Guide

provides information about the Lenovo

RackSwitch

™

G7052 (referred to as G7052 throughout this document).

The G7052 is a 1U rack-mountable aggregation switch with unmatched line-rate

Layer 2 performance. The G7052 cascades two switching fabrics that provide

simultaneous wire-speed transport of multiple packets at low latency on all ports.

The G7052 contains the following switching ports:
•

Forty-eight Gigabit Ethernet (GbE) RJ-45 ports

•

Four 10 GbE Small Form Pluggable Plus (SFP+) ports

SFP+ ports can be populated with optical or copper transceiver modules or

Direct-Attach Cables (DACs).

The G7052 has rear-to-front airflow. It is 1U in height and can be mounted

horizontally or vertically, depending on your application. Mounting options are

available for a variety of rack systems.

You can manage the switch through the local console port, or through a remote

network connection, a Web browser-based interface, or SNMP-based network

management software.

Note:

Other features supported on your switch depend on the specific firmware

installed. For more information, see the

Application Guide

and

Command

Reference

for your specific switch and its installed firmware.

G7052 Documentation

About this Installation Guide

This

Installation Guide

provides information and instructions for installing the

G7052, updating the firmware, and solving problems. For other information about

configuration and management of the switch, refer to the documents described in

“Related Documentation” on page 17

Note:

•

The illustrations in this document might differ slightly from your hardware.

•

The console output described or referenced in this document might differ slightly
from that displayed by your system. Output varies according to the type of
Lenovo chassis and the firmware versions and options that are installed.

Notices and Statements in this Document

The

caution

and

danger

statements in this document are also in the multilingual

Safety Information

document, which is on the included

Documentation

CD. Each

statement is numbered for reference to the corresponding statement in the

Safety

Information

document.

The following notices and statements are used in this document:

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды