Lenovo RackSwitch G7052 Скачать руководство пользователя страница 47

Страница: 47 / 86

Chapter 3: Installing G7052 Hardware and Options

Installing the Air-Duct Option

The G7052 supports an optional 1U air duct to maximize air flow conditions in a 19”

rack.

For information on removing an installed 1U air-duct option, see

“Removing the

Air-Duct Option” on page 65

The following table lists the parts included with the air-duct option kit.

Attention:

The rack-mounting frame may not be able to support the weight of the

networking switch with only the front post mounting brackets (2-post application). If
the switch has an undesirable amount of sag, it is recommended to use a 4-post
mounting kit.

Attention:

For earthquake stability, mount the switch in a 4-post rack.

Table 10. Air-duct Option Kit parts

Item Number

Description

Quantity

Cable tie

1U Duct sleeve (long)

Mounting bracket (left)

Mounting bracket (right)

Foam carrier assembly

M3.5 screws

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды