Lenovo ideacentre 510S Скачать руководство пользователя страница 75

Страница: 75 / 92

7. Insert the new Wi-Fi card into the M.2 Wi-Fi card slot. Ensure that the Wi-Fi card is inserted firmly. Then,

pivot the Wi-Fi card as shown so that the screw notch on the Wi-Fi card aligns with the screw hole
in the system board.

Note:

Do not touch the notched edge of the Wi-Fi card.

Figure 34. Installing the Wi-Fi card

8. Install the screw to secure the Wi-Fi card to the system board, and then connect the Wi-Fi antenna

cables to the Wi-Fi card.

Figure 35. Connecting the Wi-Fi antenna cables

9. If a PCI-Express card is available, install the PCI-Express card. See “Replacing a PCI Express card”

on page 66

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 74.

Replacing the Wi-Fi antennas

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1 .

To replace the Wi-Fi antennas, refer to the following topics:

•

“Replacing the front Wi-Fi antenna” on page 69

•

“Replacing the rear Wi-Fi antenna” on page 71

Replacing the front Wi-Fi antenna

To replace the front Wi-Fi antenna, do the following:

Chapter 6

Installing or replacing hardware

Содержание ideacentre 510S





























































































Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ideacentre 510S, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды