Lenovo ideacentre 510S Скачать руководство пользователя страница 76

Страница: 76 / 92

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 48.

3. Remove the front bezel. See “Replacing the front bezel” on page 48.

4. Locate the front Wi-Fi antenna. See “Computer components” on page 30.

5. Disconnect the front antenna cable from the Wi-Fi card module.

6. Remove the front antenna and cable from the front of the computer.

Figure 36. Removing the front Wi-Fi antenna

7. Peel off the paper that protects the stickers on the new front antenna.

Figure 37. Peeling off the paper that protects the stickers

ideacentre 510SHardware Maintenance Manual

Содержание ideacentre 510S





























































































Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ideacentre 510S, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды