Lenovo ideacentre 510S Скачать руководство пользователя страница 64

Страница: 64 / 92

13. Insert the connector and cable of the new thermal sensor into the lower hole

in the chassis. Then

align the two tabs on the plastic holder holding the thermal sensor with the two holes

and

in the

chassis, and push the plastic holder until it snaps into position.

Figure 19. Installing the new thermal sensor

14. Reconnect the thermal sensor cable to the system board. See “Parts on the system board” on page 33.

15. Reinstall the system fan assembly. See “Replacing the system fan assembly” on page 55.

16. Reinstall the front audio and USB assembly. See “Replacing the front audio and USB assembly”

on page 54.

17. Reinstall the card reader. See “Replacing the card reader” on page 53.

18. Reinstall the storage drive. See “Replacing the storage drive” on page 51.

19. Reinstall the optical drive. See “Replacing the optical drive” on page 49.

20. Reinstall the front bezel. See “Replacing the front bezel” on page 48.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 74.

Replacing the power supply assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1 .

Although there are no moving parts in your computer after the power cord has been disconnected, the
following warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

CAUTION:

Hazardous moving parts. Keep fingers and other body parts away.

ideacentre 510SHardware Maintenance Manual

Содержание ideacentre 510S





























































































Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ideacentre 510S, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды