Lenovo ideacentre 510S Скачать руководство пользователя страница 62

Страница: 62 / 92

5. Remove the storage drive. See “Replacing the storage drive” on page 51.

6. Remove the card reader. See “Replacing the card reader” on page 53.

7. Remove the front audio and USB assembly. See “Replacing the front audio and USB assembly” on

page 54.

8. Locate the system fan assembly. See “Computer components” on page 30.

9. Note the cable routing and disconnect the system fan assembly cables from the system board. See

“Parts on the system board” on page 33.

10. The system fan assembly is attached to the chassis by four rubber mounts. Remove the system fan

assembly by cutting the rubber mounts and lifting the system fan assembly out of the chassis.

Note:

The new system fan assembly comes with four new rubber mounts attached.

Figure 16. Removing the system fan assembly

11. Install the new system fan assembly by aligning the new rubber mounts that came with the new system

fan assembly with the corresponding holes in the chassis, and then push the rubber mounts through the
holes. Then, carefully pull on the tips of the rubber mounts from the bottom until the new system fan
assembly is secured in place.

Figure 17. Installing the system fan assembly

12. Reconnect the system fan assembly cables to the system board. See “Parts on the system board”

on page 33.

ideacentre 510SHardware Maintenance Manual

Содержание ideacentre 510S





























































































Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ideacentre 510S, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ideacentre 510S

Отзывы:

Бренды по названию

Популярные бренды