manualshive.com logo in svg

Lenovo ideacentre 510S, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo ideacentre 510S Скачать руководство пользователя страница 77

8. Stick the front antenna to the front panel as shown. Then insert the front antenna cable through the

hole in the front panel.

Figure 38. Installing the front Wi-Fi antenna

9. Connect the front antenna cable to the Wi-Fi card module.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 74.

Replacing the rear Wi-Fi antenna

To replace the rear Wi-Fi antenna, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 48.

3. Locate the rear Wi-Fi antenna. See “Computer components” on page 30.

4. Straighten the rear Wi-Fi antenna so that it can be more easily twisted.

5. Hold the thicker end of the rear Wi-Fi antenna and unscrew the Wi-Fi antenna from the rear of the

computer.

Figure 39. Removing the rear Wi-Fi antenna

6. Screw the new rear Wi-Fi antenna to the rear Wi-Fi antenna connector attached on the rear of the

computer.

7. Adjust the angle of the rear antenna to lower the risk of breaking the antenna by accident.

Chapter 6

.

Installing or replacing hardware

71

Содержание ideacentre 510S





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды