Lenovo 10AQ Скачать руководство пользователя страница 97

Страница: 97 / 184

4. Note the cable routing of the installed slim card reader and disconnect the cable of the slim card

reader from the system board.

5. Remove the screw that secures the slim card reader bracket and then remove the bracket from the

chassis.

Figure 20. Removing the slim card reader bracket

6. Remove the two screws that secure the card reader to the bracket. Then, slide the card reader as

shown to remove it from the bracket.

Note:

Touch only the edges of the card reader. Do not touch the circuit board of it.

Figure 21. Removing the slim card reader from the bracket

7. Take the new card reader out of the static-protective package by its sides.

8. Align the new card reader in the slim card reader bracket and slide the card reader into the rail as shown

until it stops. Then, install the two screws to secure the new card reader to the bracket.

Chapter 9

Replacing FRUs (machine type: 10AR)

Содержание 10AQ

























































































































































































Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 10AQ, Руководство по обслуживанию

Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды