Lenovo 10AQ Скачать руководство пользователя страница 149

Страница: 149 / 184

Figure 86. Installing the new slim card reader into the bracket

9. Route the cable of the new card reader through the corresponding hole for the card reader bracket in

the front of the chassis.

10. Install the bracket into the chassis so that the hole in the bracket is aligned with the corresponding hole

in the chassis. Then, Install the screw to secure the card reader bracket to the chassis.

Figure 87. Installing the slim card reader bracket

11. Connect the cable of the new slim card reader to the system board. See “Locating parts on the

system board” on page 80.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 169.

Chapter 10

Replacing FRUs (machine type: 10AQ)

145

Содержание 10AQ

























































































































































































Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 10AQ, Руководство по обслуживанию

Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды