Lenovo 10AQ Скачать руководство пользователя страница 123

Страница: 123 / 184

Figure 53. Installing the rear Wi-Fi antenna

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

Removing the rear Wi-Fi antenna

To remove the rear Wi-Fi antenna, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 85.

3. Straighten the rear Wi-Fi antenna so that it can be more easily twisted.

4. Hold the thicker end of the rear Wi-Fi antenna and unscrew the Wi-Fi antenna from the rear of the

computer.

Chapter 9

Replacing FRUs (machine type: 10AR)

119

Содержание 10AQ

























































































































































































Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 10AQ, Руководство по обслуживанию

Результаты поиска

Содержание 10AQ

Отзывы:

Бренды по названию

Популярные бренды