manualshive.com logo in svg

Lenovo 10AQ, Руководство по обслуживанию

Поделиться
Скачать
Lenovo 10AQ Скачать руководство пользователя страница 162

8. Reinstall the PCI Express x16 graphics card if you have removed it.

9. Lower the drive bay assembly.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 169.

Replacing the system board

CAUTION:

The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before opening the computer cover.

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

Safety, Warranty, and Setup Guide

that came with your computer. To obtain a copy of the

Safety, Warranty, and

Setup Guide

, go to:

http://www.lenovo.com/support

This section provides instructions on how to replace the system board.

To replace the system board, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 126.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 127.

4. Pivot the optical drive bay assembly upward to gain access to the system board. See “Accessing the

system board components and drives” on page 128.

5. Remove all memory modules and PCI cards that are currently installed. See “Installing or replacing a

memory module” on page 156 and “Installing or replacing a PCI card” on page 153.

6. Remove the heat sink and fan assembly from the failing system board. See “Replacing the heat sink and

fan assembly” on page 129.

7. Carefully take note of the location of all cable connections on the system board and disconnect all the

cables. See “Locating parts on the system board” on page 80.

8. Remove the eight screws that secure the system board.

158

ThinkCentre E93 Hardware Maintenance Manual

Содержание 10AQ

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды