manualshive.com logo in svg

Lenovo 10AQ, Руководство по обслуживанию

Поделиться
Скачать
Lenovo 10AQ Скачать руководство пользователя страница 124

Figure 54. Removing the rear Wi-Fi antenna

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

Installing or removing the front Wi-Fi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

Safety, Warranty, and Setup Guide

that came with your computer. To obtain a copy of the

Safety, Warranty, and

Setup Guide

, go to:

http://www.lenovo.com/support

This section provides instructions on how to install or remove the front Wi-Fi antenna.

Installing the front Wi-Fi antenna

To install the front Wi-Fi antenna, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 85.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 86.

4. Peel off the paper that protects the stickers on the front antenna.

120

ThinkCentre E93 Hardware Maintenance Manual

Содержание 10AQ

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды