Lennox XC25-024-230-01 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 72

Lennox XC25-024-230-01 Скачать руководство пользователя страница 64

64

XC25

OUTDOOR

AMBIENT

LIQUID LINE

TEMPERATURE

SENSOR HARNESS

BLACK WIRES WITH

BLACK

SLEEVE

BLACK WIRES WITH

YELL0W

SLEEVE

SENSOR

RESISTANCE VALUES

RANGE (OHMS)

TEMP RANGE ºF

(ºC)

PIN# / WIRE

SLEEVE COLOR

LIQUID LINE

OUTDOOR

AMBIENT

NONE

4 AND 3

(

BLACK

)

6 AND 5

2 AND 1

(

YELLOW

)

-40 (-40) TO

140 (60)

336,000 to 2,487 (see
table 15 on page 65 for
exact temperature to
ohm readings).

314669 and 3779

N/A

Figure 50. Temperature Sensor Specifications

CHECKOUT

Sensors connect to the outdoor control through a field‐replaceable harness assembly that plugs into the outdoor control.
Through the sensors, the control detects outdoor ambient, coil and liquid temperature fault conditions. As the detected tem
perature changes, the resistance across the sensor changes. Check sensor operation by reading ohms across pins shown
in figure 50.

NOTE - When checking the ohms across a sensor, be aware that a sensor showing a resistance value that is not within the
range shown in figure 50, may be performing as designed. However, if a shorted or open circuit is detected, then the sensor
may be faulty and the sensor harness will need to be replaced.

OUTDOOR AMBIENT

TEMPERATURE

SENSOR

LIQUID LINE SENSOR

CRANKCASE HEATER

THERMOSTAT (S40) OPENS AT

70ºF, CLOSES AT 50ºF

Figure 51. Temperature Sensor Locations

«
...
62
63
64
65
66
...
»

Содержание XC25-024-230-01









































































Отзывы:

Нет отзывов